Help me setup Dataone in Sabayon 1.1 Pro Edition

Brothers i have installed Sabayon 1.1 Pro Edition in my office PC. I used pppoe-setup to configure my Dataone and entered correct values ( have used this in Fedora & Arch too).
I connect twith pppoe-start and and did ifconfig and found ppp0 connected.
But i am not able to open any site (used firefox & konqueror). So i thought may Kmyfirewall is blocking me so i uninstalled it

and reconfigured Dataone and this time chose "1" as firewall setup in pppoe-setup but the problem persists.
SO i came back to Arch setup and used pppoe-setup and everything was fine.
I read Gentoo Network wiki and all stuff but it just doent work, though it connects as shown by o/p of ifconfig below

ppp0 Link encapoint-to-Point Protocol
inet addr:59.93.206.119 P-t-P:59.93.192.1 Mask:255.255.255.255
UP POINTOPOINT RUNNING NOARP MULTICAST MTU:1492 Metric:1
RX packets:3045 errors:0 dropped:0 overruns:0 frame:0
TX packets:2795 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:3
RX bytes:2514542 (2.3 Mb) TX bytes:638401 (623.4 Kb)

eth0 Link encap:Ethernet HWaddr 00:11:11:0D:5EB
inet addr:192.168.1.2 Bcast:192.168.1.255 Mask:255.255.255.0
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:3132 errors:0 dropped:0 overruns:0 frame:0
TX packets:2910 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:2588074 (2.4 Mb) TX bytes:708072 (691.4 Kb)

lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:96 errors:0 dropped:0 overruns:0 frame:0
TX packets:96 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:6000 (5.8 Kb) TX bytes:6000 (5.8 Kb)

I am sure it some firewall jhol-jhaal, so how should i go about stopping iptables and configure Datone.
I can ping my router (utstar200R)
Plz help

M

Check iptables rules

Code:

iptables -L

Remove a service from startup

Code:

rc-config delete <servicename> default

Why is there an address associated with eth0, if I remember correctly, if you're using ppp then eth0 will not have any address.

This is my iptables -L o/p

iptables -L
Chain INPUT (policy ACCEPT)
target prot opt source destination

Chain FORWARD (policy ACCEPT)
target prot opt source destination

Chain OUTPUT (policy ACCEPT)
target prot opt source destination

I dont know anything about iptables.

What is the purpose of the removing the service and what service to remove??
Will that revert iptables service to default?

M

There are no iptables rules. It's not a firewall problem then. Start looking towards your network setup.

I was fiddling in the Live Mode and used this as PPP configuration

Basic Setup File: /etc/conf.d/net
config_eth0=( "null" )

config_ppp0=( "ppp" )
link_ppp0="eth0"
plugins_ppp0=( "pppoe" )

username_ppp0='your-ISP-username-here'
password_ppp0='your-ISP-password-here'

pppd_ppp0=(

"noauth"
"defaultroute"
"usepeerdns"
"default-asyncmap"
"ipcp-accept-remote"
"ipcp-accept-local"
"lcp-echo-interval 15"
"lcp-echo-failure 3"
"mru 1492"
"mtu 1492"
"debug"
)

but it didnt work. SO i used this

config_eth0=( "dhcp" )
dhcp_eth0="release nodns nontp nonis nogateway nosendhost"

and started the connection /etc/conf.d/net.ppp0 start and after some seconds i was able to connect and surf

But when i used the same procedure in the actual installed-system, it did the same tantrums. Getting connected but no luck with surfing .The light on my modem blinks as if data is passing through but....

M

You either configure to use ppp or dhcp, not both.
Can you explain how you configure your connection in other distros?
Also check route

Code:

route -n

And try pinging the available gateway(s).

or

netstat -r

*s269.photobucket.com/albums/jj44/visio159/Unismilies/74.png

Well i used pppoe-setup in my Arch Linux box, so i tried that in Sabayon and then did the Modular Networking way as described in Gentoo Wiki and it did work ONCE in Live Mode but thats it.

@mehulved: So what changes should i do in those files??

M

remove the last couple of lines related to eth0, it shouldn't be configured.
Maybe you haven't added ppp0 in the list of network interfaces to be started at boot up?

Help me setup Dataone in Sabayon 1.1 Pro Edition | Firewall