DIGIT-ARC read-only archive · snapshot: July 23, 2026

N150 D-Link DSL-2730U WiFi but no signal in next room

16 posts · originally from https://geek.digit.in/community/threads/n150-d-link-dsl-2730u-wifi-but-no-signal-in-next-room.160235/

sling-shot
sling-shot Original post #1
Jul 17, 2012 at 11:11 PM
D-Link Wireless N 150 ADSL2+ 4-Port Router

I have this D-Link DSL-2730U router modem installed on my desktop. I am not getting regular signal in the adjoining bedroom for my mobiles. This should not be normal because the net distance is less than 5 metres.

I have attached a rough drawing of the situation. What can be done to improve the signal strength in the room?

*img17.imageshack.us/img17/8249/wifisignalproblem.png
saswat23
Jul 18, 2012 at 9:12 AM
AFAIK almost all D-Link routers these days are having problems. Even my bro has this very model and the connection drops regularly. His room design is almost same as yours. He just gets only 1 bar in his bedroom. Even in the same room where modem is kept, signal is 4 most times. Getting full signal is just like a dream.
Also I couldnt connect my mobile to WiFi even after applying the password/sec.key.
Being such a good brand D-Link has terrible problems.

BTW go to router's config. Page and see if it enabled to support 'b' and 'g' wifi devices. If its disable, enable.
This might help.
sriharsha_madineni
Jul 18, 2012 at 9:30 AM
@OP
Try placing the router above head level and away from the computer if possible. That should improve the signal a bit.
sling-shot
Jul 18, 2012 at 2:05 PM
@OP
Try placing the router above head level and away from the computer if possible. That should improve the signal a bit.

I cannot move it much right now because of short length of power cable and LAN cable. Will try to put it as far and as high as possible and test.
saswat23
Jul 18, 2012 at 5:51 PM
Use an Extension Cord and see if that helps.
sling-shot
Jul 18, 2012 at 8:30 PM
BTW go to router's config. Page and see if it enabled to support 'b' and 'g' wifi devices. If its disable, enable.
This might help.

It is currently in "802.11n Auto" mode. There is an option to make it 802.11n only.

Use an Extension Cord and see if that helps.

Tried placing the router above head level but could not reach the network cable up to that height. Signal strength seems to have improved. Now I get consistently one bar with LWW and at least poor signal level with E6.

Will get a longer network cable tomorrow and see if I can browse with this setup.
papul1993
Jul 18, 2012 at 10:33 PM
Get a directional antenna. Or make one yourself.
sling-shot
Jul 18, 2012 at 10:41 PM
Had Digit published a guide sometime?
sriharsha_madineni
Jul 19, 2012 at 12:07 AM
Had Digit published a guide sometime?

Yes it was, long back 2010 or 2009 Anniversary issue may be.

But placing it at a high point fixes most of the issues usually. If the situation hasn't improved even after that, then getting a repeater is ideal instead of antenna.

And check for interference, modern homes are filled with loads of them ;-)
sling-shot
Jul 20, 2012 at 1:35 AM
Placing the router higher has not improved actual browsing by much although generally one bar signal is visible.

The antenna can be either horizontal or vertical. Does it have anything to do with the direction in which signal gets thrown?

I got a longer network cable.

What equipment may cause interference?
S
Aug 10, 2012 at 1:04 AM
D-Link Wireless N 150 ADSL2+ 4-Port Router

I have this D-Link DSL-2730U router modem installed on my desktop. I am not getting regular signal in the adjoining bedroom for my mobiles. This should not be normal because the net distance is less than 5 metres.

I have attached a rough drawing of the situation. What can be done to improve the signal strength in the room?

*img17.imageshack.us/img17/8249/wifisignalproblem.png

Dude, try getting ASUS 5dbi high gain antenna, which will help you in extending the range in your existing model
Renny
Renny #12
Aug 10, 2012 at 12:29 PM
1. Make a directional antenna using cardboard and metal foil.

2. Place the router at a height, like above a cupboard or something.

3. Install some custom firmware and tweak the transmitting power.

Using the above method I'm getting 5/6 bars signal from 4 rooms away.
saswat23
saswat23 #13
Aug 11, 2012 at 12:43 AM
1. Make a directional antenna using cardboard and metal foil.

3. Install some custom firmware and tweak the transmitting power.

Using the above method I'm getting 5/6 bars signal from 4 rooms away.

1. How to do that exactly :)

3. Wont that void warranty! :/:|
dashing.sujay
Aug 11, 2012 at 1:28 AM
Even a "b/g" router is supposed to work. The distance is too close. It must work, something is wrong.
sling-shot
Aug 11, 2012 at 11:48 PM
Even a "b/g" router is supposed to work. The distance is too close. It must work, something is wrong.

That is what I am thinking too. But I have only this one at present and not willing to buy another one. If I send it for service, I will be without anything during that time.
dashing.sujay
Aug 12, 2012 at 12:30 AM
^Try resetting it once. (Hardware reset).