no signal error · DIGIT-ARC

Hi,
I'm getting no signal error while my cpu works fine.I think its not the problem with cable,because when i looked in the internet i saw a solution-to pull off the power cord from the back and press the power button infront for 45 seconds and start again.
It works everytime ,but im tired of pulling off the chord and pressing buttons before everytime i boots up my pc

Why is this error caused? Isnt there a permanent solution :-?

?
Thank You

Do other monitors work proerly with your PC and does your monitor work properly with other systems?

harshilsharma63 said:
Do other monitors work proerly with your PC and does your monitor work properly with other systems?

I dont have an extra monitor or pc

A

Nanducob said:
Hi,
I'm getting no signal error while my cpu works fine.I think its not the problem with cable,because when i looked in the internet i saw a solution-to pull off the power cord from the back and press the power button infront for 45 seconds and start again.
It works everytime ,but im tired of pulling off the chord and pressing buttons before everytime i boots up my pc
Why is this error caused? Isnt there a permanent solution?
Thank You

Link to the article?

Nanducob said:
I dont have an extra monitor or pc

Then arrange one, probably from neighbours.

pressing the power button means resetting your cmos battery or something like that, maybe the battery is cause of your problems

Can you post a screen shot of the problem that occurs with your monitor.

imo, a screenshot of the monitor isnt necessary/wont be much of help...

P.S.- Bavusani are you trying to increse your post count?

R

flyingcow said:
imo, a screenshot of the monitor isnt necessary/wont be much of help...

P.S.- Bavusani are you trying to increse your post count?

lol

^^

arijitsinha said:
Link to the article?

sorry i just seached and landed on one article yesterday,today im not getting that page

flyingcow said:
pressing the power button means resetting your cmos battery or something like that, maybe the battery is cause of your problems

i assuming that the cmos takes care of time and that stuff.so resetting it wont change the date?
in my case-no

Nanducob said:
sorry i just seached and landed on one article yesterday,today im not getting that page
i assuming that the cmos takes care of time and that stuff.so resetting it wont change the date?
in my case-no

hmm, imo it takes care of the settings etc, i also had the no signal errors, its very frustrating
but the problem was gone when i pressed the button for 10 sec, only once...

try re-seating rams.
reset cmos.
make sure the temperature is fine.

bavusani said:
Can you post a screen shot of the problem that occurs with your monitor.

Read the whole content first

capture the whole thing with a digicam and then post

vidhubhushan said:
capture the whole thing with a digicam and then post

already posted the real screenshot

,you were late

@all:thanks and i will try.till now no problem

W

if it happens again disconnect all peripherals(hard disks,dvd drive etc) & take out the mobo+cpu out of cabinet.place it on a newspaper/cardboard & connect psu & power button cable of cabinet & then try.if it boots up normally then there is some grounding issue inside cabinet.

whitestar_999 said:
if it happens again disconnect all peripherals(hard disks,dvd drive etc) & take out the mobo+cpu out of cabinet.place it on a newspaper/cardboard & connect psu & power button cable of cabinet & then try.if it boots up normally then there is some grounding issue inside cabinet.

Yeh i will try if it happens again,

Nanducob said:
already posted the real screenshot,you were late

@all:thanks and i will try.till now no problem

that comment was not for you friend

It happened again.
How to take out gfx card?its not coming out

W

in the meantime try my previous suggestion with graphics card installed.

Nanducob said:
It happened again.
How to take out gfx card?its not coming out

did you remove the thingy that holds the gpu and pcie slot?
and also remove the screws attached to thecabinet(attached to the gpu)

whitestar_999 said:
in the meantime try my previous suggestion with graphics card installed.

Ya sure.some electricity is leaking in cabinet though plugpoint is fine

flyingcow said:
did you remove the thingy that holds the gpu and pcie slot?
and also remove the screws attached to thecabinet(attached to the gpu)

No lol. I should have ripped it then

Nanducob said:
It happened again.
How to take out gfx card?its not coming out

in pcie slot ,there is a small holder. check it