DIGIT-ARC read-only archive · snapshot: July 23, 2026

Problem with PC startup!!!!!

11 posts · originally from https://geek.digit.in/community/threads/problem-with-pc-startup.167318/

K
kryptex Original post #1
Dec 8, 2012 at 7:49 PM
Hello,
My friend has a PC with following Specs:
Intel Core2Quad Q8400
4GB DDR2 RAM 800 MHz
GTX 560 (non ti)
PSU of VIP(dunno W)
He ran burn-in test (stress test ) for both CPU n GPU simultaneously... (Temps were below max level) He says the tests were completed successfully.
Now the problem is the PC wont even boot. So hat could be the problem? Which components might have been damaged???
topgear
topgear #2
Dec 9, 2012 at 4:20 AM
when you start the pc cpu fan is running ? Do your mobo has onboard gfx ? ( can you hear any beep sound ? )

use another PSU, remove the gfx card and test with onboard gfx port of mobo or another gfx card. If no go remove and remount the cpu hsf and cpu properly - make sure you apply TiM before remounting the cpu hsf - post feedback. Remove and remount ram modules - Also check with some other ram slot and if possible ram module.
F
Dec 10, 2012 at 11:12 AM
Hello,
My friend has a PC with following Specs:
Intel Core2Quad Q8400
4GB DDR2 RAM 800 MHz
GTX 560 (non ti)
PSU of VIP(dunno W)
He ran burn-in test (stress test ) for both CPU n GPU simultaneously... (Temps were below max level) He says the tests were completed successfully.
Now the problem is the PC wont even boot. So hat could be the problem? Which components might have been damaged???

Hi for what reason your friend ran a stress test????
K
kryptex #4
Dec 14, 2012 at 3:13 PM
Nope. My friend told fan's not running. No beep sound either. He has a spare motherboard, which he used but same problem. He even checked the PSU cables on other PC,cables are fine.

Hi for what reason your friend ran a stress test????

He wanted to check the performance and stability ...
topgear
topgear #5
Dec 15, 2012 at 3:34 AM
most probably the cpu has gone.
F
Dec 15, 2012 at 11:37 AM
Hello,
My friend has a PC with following Specs:
Intel Core2Quad Q8400
4GB DDR2 RAM 800 MHz
GTX 560 (non ti)
PSU of VIP(dunno W)
He ran burn-in test (stress test ) for both CPU n GPU simultaneously... (Temps were below max level) He says the tests were completed successfully.
Now the problem is the PC wont even boot. So hat could be the problem? Which components might have been damaged???

If nothing happens he press the power button no lights turn on than he can try replacing psu.
topgear
topgear #7
Dec 16, 2012 at 5:55 AM
Nope. My friend told fan's not running. No beep sound either. He has a spare motherboard, which he used but same problem. He even checked the PSU cables on other PC,cables are fine.

He wanted to check the performance and stability ...

I think Op wanted to say that his friend has checked the PSu on some other pc.
F
Dec 18, 2012 at 12:22 PM
so his psu is working fine???????????
patkim
patkim #9
Dec 18, 2012 at 3:23 PM
While there could be advanced issues like bad CPU, faulty PSU etc..it’s also worth checking some basics as well since the PC is completely dead.

Make sure all power cables are tightly connected & also PSU is getting mains power properly i.e. mains power cable is not faulty

Also the power switch (button) on the cabinet front panel might have gone bad..short the pins on mobo where it connects and check if PC powers up.
anirbandd
anirbandd #10
Dec 18, 2012 at 8:10 PM
stress test on VIP psu?? :facepalm:

maybe one of the following
1. psu gone kaput.
2. psu gone kaput, taking with it the cpu.
3. psu gone kaput, taking with it the gpu.
4. psu gone kaput, taking with it the cpu and gpu.

see which of the fan on psu, cpu, gpu are not running.
if psu fan is not running, then psu is gone. test the system with a good psu[maybe you can lend him yours. just dont let him stress test again :p ].
test the system part by part, and you will get the faulty part.
topgear
topgear #11
Dec 19, 2012 at 5:09 AM
sometime this type of stsrtup issue occurs if mobo somehow comes in contact with the metal part of the cabinet - so if Op is going to try with a new psu he better do the test placing the mobo outside of the cabinet on a table connecting only the PSu, monitor, keyboard and gfx card if needed ( no mobo IGP ).